ARGB

Good RGB – Installing A-RGB fans with a non RGB motherboard

Today we’re setting up some ARGB fans with a motherboard that doesn’t have any RGB or ARGB headers to see what’s involved. We’ll also be controlling these via software, so we can enjoy all the customisation options that come with the latest addressable RGB kits!

For this we’re going to be using our favourite Cooler Master ARGB 3x Fan Kit as it has a fan controller included, before we get stuck into the install we’ll just take a quick look at what comes inside the box.

– A-RGB LED Small Controller
– SATA & Thermal Detection Cable
– 1 to 3 A-RGB Cable & Cable to sync MB
– 1 to 3 Fan Power Cable Splitter
– Thermal Detector
– 3x 120mm A-RGB Fans
– 12 Fan Screws
– User Manual + Warranty Information Booklet

OK let’s get into it! (insert great pic from manual)

First, we connected the ARGB Cable (it’s got 3 pins, shown below) and the Fan Power Cable Splitter (ignoring the Asus and Gigabyte connectors) to the appropriate connectors on the fan cables. The ARGB and Fan Power connector types are clearly marked on the cables with white tags. The green arrows below show the little triangles that match up.

We then connected the ARGB Cable 5 pin connector and the SATA & Thermal Detection Cable 4 pin connector to the controller.

Finally, we connected the SATA & Thermal Detection Cable into the Thermal Detector and SATA power connector from the PSU.

When turning on the PC we had success, the fans were running fine and the LEDs lit up – able to be controlled through the buttons on the ARGB controller.

With everything running as it should, we then started fitting these new components within the gaming PC. For maximum visibility, we’ve replaced both fans on our CPU cooler and installed the third fan onto the rear of the case. Given this setup involves the CPU cooler, the splitter cable was removed and the power cables for the fans were instead connected directly to the motherboard.

The ARGB controller is easy to mount into the case as it is magnetic, and with you’ll have a few static colours, cooler effects and the beautiful ARGB rainbow mode – but we want software controls for more customisation options!

The Manual that comes in the box states you can download software on Cooler Master’s website. We definitely wanted to see if we could make use of the controller to configure the fans through software, so we loaded up Cooler Master’s website to take a look. However, the download tab on the ARGB Controller and this Fan kit’s page had no software or firmware to download (we’ve let them know, by the time you read this it has quite possibly been updated)

After searching the MasterLiquid ARGB pages we found that they had the following downloads though, so we continued on!

ARGB BOX Firmware (This is the newer, correct version rather than the one we originally used, which was v1.0.0.1)
ARGB Lighting Control Software v0.0.86 (There is a new software package to control everything now, named MasterPlus+, you can download it here)

This fan kit doesn’t actually come with a MicroUSB cable or internal USB Header adapter but luckily we had one, after connecting the controller via that cable and adapter we installed the Software but weren’t able to detect the controller...

So we then went on to installing the firmware which allowed us to detect the controller as the larger 4 port version 🙂

PLEASE NOTE: This may affect the functionality of the temperature detection

Now, onto connecting the Fans and Controller through the software 🙂

Here we opened up the detected controller and then navigated to the configuration page.

Once on the configuration page, we added the single MasterFan ARGB option (indicated by the double light bulb icon) via the + symbol. (The MasterLiquid options also work but aren’t really needed since the controller only has one port to control.)

This will add the fan into the top left-hand corner, next, we click on the light bulb icon of the added fan.

Then connect that to the first controller port by clicking on the light bulb icon with the A1 next to it.

OK, now that tricky bit is done, we can begin changing the LED modes and individual LED colours! As we have our fans connected to the first port on our controller we can configure and customize through the overview tab.

From the overview tab, you can select the different patterns for the LEDs.

PLEASE NOTE: Due to changing the firmware the button on the controller that cycles the modes is changed to match this order.

– Motherboard (Dark Blue)
– Spectrum Cycle
– Single Slide Mode
– Double Slide Mode
– Breathe Mode
– Accumulate Mode
– Demo Mode
– Customization
– Turn Off

If you select the Customization option you can select the colour for each individual LED!

Ahhh that was both tricky and fun 🙂 ARGB fans can definitely work on motherboards that don’t have RGB or ARGB headers and can be configured using the software. Remember that the Cooler Master ARGB MasterFan Kit includes a controller, but you might need to get your own MicroUSB cable and internal USB Header adapter for it to look super clean 😛 (cowboy mode plugging the micro USB cable into a USB port on the outside of your PC work though)

LED ON!